|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
Now, Yes. NetSwitch II-M has to be located between internal Hub and external Hub. |
||||||||||||
Like this, it requires two Hubs for internal and external network. So we would say that you need |
||||||||||||
one additional Hub. |
||||||||||||
But, we plan to embed Switching Hub in NetSwitch II-M sooner or later. Then you do not need |
||||||||||||
additional Hubs for external network. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
NetSwitch II-M separates your network into internal and external network physically on a |
||||||||||||
single network cable. That means that there is not any physical network connection between |
||||||||||||
internal and external network. Fundamentally, it is impossible for any hackers to intrude into |
||||||||||||
your internal network. Thus you can secure your internal network from the intruders outside. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
NetSwitch II-M supports 24 UTP (10/100Mbps) ports. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
No, users who use NetSwitch II-M transmit and receive the data only through Hub and NIC. |
||||||||||||
NetSwitch II-M does not control any packet. It just repeats the packet. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
No, But you can check NetSwitch II-M status through LED in front. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
It supports all of protocols. It does not control any data flowing on the network. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
Yes, it is very simple in operation. Only one drawback of NetSwitch II-M is that you can not use |
||||||||||||
internal and external network at the same time. Whenever you want to access into the other |
||||||||||||
network from the current network, you have to switch the network through IPChanger, a bundle |
||||||||||||
program of NetSwitch II-M. But it just takes 1.5 seconds to switch the network. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
Basically, In case of a single network cable, there are two kinds of network traffics, internal and |
||||||||||||
external network traffic. But, If you separate your network into internal and external network |
||||||||||||
physically, it is quite natural that internal network traffic only flows on the internal network |
||||||||||||
and external network traffic flows on the external network. So it is possible that you can reduce |
||||||||||||
the internal network traffic up to 50% |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
Yes, you need to install IPChanger, a bundle program of NetSwitch II-M, on your PC. |
||||||||||||
You can switch the network into another by clicking the icon of IPChanger. If you click the icon |
||||||||||||
of IPChanger, IPChanger generates a special packet and sends the packet to NetSwitch II-M. |
||||||||||||
Then NetSwitch II-M analyzes the packet in order to decide whether to connect or disconnect |
||||||||||||
the network. Thus you must install IPChanger on your PC, in order to use NetSwitch II-M. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
Yes, you should use two IP addresses for internal and external network. In addition, you can |
||||||||||||
separate your gateway, DNS, and then some according to your policy. But you can set your IP |
||||||||||||
addresses on the same IP addresses as you use one IP address. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
No, you do not need to reboot your computer. If you click the icon of IPChanger, IPChanger |
||||||||||||
converts your IP address automatically without any system reboot. |
||||||||||||
|
||||||||||||
|
||||||||||||
|
||||||||||||
Copyright by FNET(C) since 1998, All rights reserved |